Beschrijving
The SolarMaax 200 Tropic 12 volt is a great choice for serious offshore racers and offshore cruisers. The SolarMaax is lightweight, simple, super-compact, easy to install and maintain, reliable and durable. With its diaphragm feed pumps in parallel, it can be run on a single pump for high efficiency or two pumps for high output.
The Solarmaax uses the hydraulically improved Clark Pump amplifier and Energy Recovery System that sets a new industry standard for maximum efficiency. Where high output is needed when space is limited, this is our best solution.
Because of its super low consumption, the system can be run on solar, wind or any high-power Electromaax alternator. Longer cylinders in the Enhanced Clark pump make ALL SolarMaax watermakers the quietest on the market. The system includes a complete installation kit, handheld salinity sensor, automatic flush, product sample valve.
For 12 years, Electromaax has been producing D.C. watermakers. In that time, SolarMaax has become the primary energy source for most serious cruisers. What was needed was a high-efficiency watermaker that used the minimum amount of energy while maintaining the highest quality drinking water that the 21″ diaphragm can achieve. Optional up to 10 years guarantee.
Specs
- Extremely quiet
- Super high water output
- Drinking water of the highest quality
- Compact with a single 21″ diaphragm
- Automatic rinsing and timed re-rinsing
- Control panel with gauges and control switches
- Can operate in a wider range of seawater temperature and salinity
- Easy to maintain
- Very easy installation both electrically and mechanically, even for the do-it-yourselfer
- Super lightweight
- Most energy-efficient water maker to date, 10DC amp at 12 volts generates 38 litres per hour
- No own consumables
- Military-grade components using titanium components in critical areas allowing higher pressure, resulting in higher output
Production Rate:
7.5-13 Gallons per hour, 28-50 litres per hour
The production rate is set by the displacement of the Enhanced Clark Pump energy recovery
device and the feed flow rate. The SolarMaax 200 tropic uses a 10% displacement Enhanced
Clark Pump so 10% of the feed water flow is turned into product water. Water temperature
and salinity affect operating pressure but have little effect on production rate. Changes in
feed flow do have an effect, the more feed flow the more product. Supplying good voltage to
the feed pump gives the best production rate. Running the system while the batteries are
bulk charging gives the highest production rates.
RO Membrane:
One standard seawater RO 2521 Membrane element
Membrane Type: Polyamide Thin-Film Composite
Range of Operating Pressures: 650 to 1000 psi (45 to 69 bar)
Normal Operating Pressure: Set by feed water conditions and feed flow rate.
Salt Rejection rate: 99.4%
Maximum Operating Temperature: 113°F (45°C)
Minimum Storage/Operating Temp: 32°F (0°C)
Maximum Operating Pressure: 1,000 psi, (69 bar)
Maximum Pressure Drop: 15 psi (1 bar)
pH Range, Continuous Operation: 2-11
pH Range, short-term cleaning: 1-12
Free Chlorine Tolerance: <0.1ppm
Electrical Power Requirements:
8-10 amps @ 12.5-14.4 VDC, 15 amp fuse/breaker
4-5 amps @ 25.0-28.8 VDC, 7.5 amp fuse/breaker
The Enhanced Clark Pump Hydraulic Pressure Intensifier:
Manufactured by Electromaax for marine and military use. The Clark Pump uses the
Feed/Boost pump flow pressure to intensify the pressure of the flow through the RO
membranes high enough for reverse osmosis to occur. There are no electrical components.
Displacement: 10 %
Pressure Intensification Ratio: 10:1
Feed Flow range: 1.0 gpm (3.78 lpm) to 4.0 gpm (15.14 lpm)
Maximum Inlet pressure: up to 125 psi (8.6 bar)
Maximum Working Pressure: 1000 psi (68.9 bar)
Maximum operating temperature: 113°F (45°C)
Maximum storage temperature: 140°F (60.0°C)
Dimensions: 26.38" (67cm) W, 5.75" (14.6cm) D, 8.0" (20.32cm) H
Pressure Relief Valve: Manually open 1⁄2 turn for priming and servicing.
Feed Pump:
Motor: Permanent magnet type, fully enclosed with heat sink, 1/8 hp
Pump Body: Thermoplastic
Pump Type: 3 chamber diaphragm
Typical Amp Draw: 8 to 10 amps @ 12VDC, 4-5 amps @ 24VDC
Recommended fuse size: 15 amps @ 12VDC, 4.5 amps @ 24VDC
Average Flow Rate: 1.4 gpm (5.3 lpm) each
Pressure Vessel:
Filament wound fibreglass/epoxy composite vessel using non-metallic easily removable
endcaps for membrane replacement and larger than standard internal porting and fittings for
increased energy efficiency.
The most compact complete assembly available
Max pressure 1000 psi (69 Bar)
Burst pressure 3000 psi (207 Bar)
Prefilter and Auto Fresh Water Flush Filter housings:
Industry standard, 10-inch, plastic, filter housings. Accepting 9.75" by 2.5" high flow carbon
filter elements and pleated 5-micron pre-filter elements.
Controls:
Level 1 electronics in an enclosure for remote control, Auto-Flush, status LEDs and manual
over-ride switch for emergency operation
Remote control panel with Pump and Auto-Flush control switches, Flow Meter and Product
Diversion Valve for testing and servicing.
Clark Pump and Pressure Vessel Assembly:
Clark Pump and Membrane mounted on a frame and pre-plumbed with HP hoses
Dimensions: 12.1" (307 mm) W, 24.7" (630 mm) L, 8.4" (213 mm) H
Weight: 30.0 lbs. (14 kg)
Feed Pump Assembly:
The Feed Pump, Prefilter and Electronic Control Module mounted, wired and pre-plumbed on
a frame with isolation dampeners
Dimensions: 9.7" (247 mm) W, 6.7" (170 mm) D, 13.6" (345 mm) H
Weight: 14.6 lbs. (6.6 kg)
